Knowledgebase

How to Install Netdata on Linux - CentOS, Debian, Ubuntu, and Other Distros Print

  • 0

Introduction

Netdata is a free, open-source, real-time monitoring tool that is actively maintained, easy to set up, and ships with a beautiful dashboard UI accessible using a web browser. Using Netdata, you can easily monitor every parameter of your Rcs instance in real-time with little to no overhead. Netdata is very lightweight and requires at most 1% CPU and about 20MB of RAM in most cases.

Netdata comes with a setup script that can be run on different distributions with ease. The setup script supports the following distributions:

  • Arch
  • Gentoo
  • Debian
  • Ubuntu
  • Sabayon
  • CentOS
  • Redhat
  • Fedora
  • OpenSUSE
  • SUSE

Installation

To install Netdata with the official installation script:

  1. Make sure you run bash for your shell

     $ bash
  2. Install Netdata directly from GitHub source

     $ bash <(curl -Ss https://my-netdata.io/kickstart.sh)

If no errors occur during installation, the Netdata daemon will start.

What this script does:

  • Detects the distro and installs the required system packages for building Netdata (will ask for confirmation).
  • Downloads the latest Netdata source tree to /usr/src/netdata.git.
  • Installs Netdata by running ./netdata-installer.sh from the source tree.
  • Installs netdata-updater.sh to cron.daily, so your Netdata installation will be updated daily (you will get a message from cron only if the update fails).

After running the kickstart.sh script, Netdata installs all requirements using your linux native package manager, then proceeds to install itself.

Using Netdata dashboard

After the installation phase, you may simply browse to http://192.0.2.123:19999 to access Netdata.

Replace the example IP address, 192.0.2.139, with your address.

Change the Default Port

To change the default web UI port to a custom port:

  1. Edit the config file.

     $ sudo vi /etc/netdata/netdata.conf
  2. In the [web] section, uncomment the following line and change the port number.

     # default port = 19999
  3. Restart Netdata.

     $ sudo systemctl restart netdata

Control the Netdata Service

You can control Netdata like a regular service with the following commands on a system that uses SystemD.

Start netdata service:

$ sudo systemctl start netdata   

Stop netdata service:

$ sudo systemctl stop netdata    

Restart netdata service:

$ sudo systemctl restart netdata 

Status of the netdata service:

$ sudo systemctl status netdata  
Introduction Netdata is a free, open-source, real-time monitoring tool that is actively maintained, easy to set up, and ships with a beautiful dashboard UI accessible using a web browser. Using Netdata, you can easily monitor every parameter of your Rcs instance in real-time with little to no overhead. Netdata is very lightweight and requires at most 1% CPU and about 20MB of RAM in most cases. Netdata comes with a setup script that can be run on different distributions with ease. The setup script supports the following distributions: Arch Gentoo Debian Ubuntu Sabayon CentOS Redhat Fedora OpenSUSE SUSE Installation To install Netdata with the official installation script: Make sure you run bash for your shell $ bash Install Netdata directly from GitHub source $ bash <(curl -Ss https://my-netdata.io/kickstart.sh) If no errors occur during installation, the Netdata daemon will start. What this script does: Detects the distro and installs the required system packages for building Netdata (will ask for confirmation). Downloads the latest Netdata source tree to /usr/src/netdata.git. Installs Netdata by running ./netdata-installer.sh from the source tree. Installs netdata-updater.sh to cron.daily, so your Netdata installation will be updated daily (you will get a message from cron only if the update fails). After running the kickstart.sh script, Netdata installs all requirements using your linux native package manager, then proceeds to install itself. Using Netdata dashboard After the installation phase, you may simply browse to http://192.0.2.123:19999 to access Netdata. Replace the example IP address, 192.0.2.139, with your address. Change the Default Port To change the default web UI port to a custom port: Edit the config file. $ sudo vi /etc/netdata/netdata.conf In the [web] section, uncomment the following line and change the port number. # default port = 19999 Restart Netdata. $ sudo systemctl restart netdata Control the Netdata Service You can control Netdata like a regular service with the following commands on a system that uses SystemD. Start netdata service: $ sudo systemctl start netdata Stop netdata service: $ sudo systemctl stop netdata Restart netdata service: $ sudo systemctl restart netdata Status of the netdata service: $ sudo systemctl status netdata

Was this answer helpful?
Back

Powered by WHMCompleteSolution